Skip to main content
GW Instek GDS-2000HD/HG Series 12-bit Digital Storage Oscilloscope
GW Instek GW Instek

GDS-2000HD/HG Series 12-bit Digital Storage Oscilloscope

Oscilloscopes

GW Instek GDS-2000HD/HG 4-channel 12-bit oscilloscope, 250/350/500 MHz, 2.5 GSa/s, up to 500 Mpts memory and an Android touch interface; HG models add a 2-channel 50 MHz arbitrary function generator. Available in India from GSAS Micro Systems.

Bandwidth

250 / 350 / 500 MHz, 4 channels + EXT

Vertical Resolution

12-bit ADC (4096 levels)

Sample Rate

2.5 GSa/s (half channels), 1.25 GSa/s (all channels)

Record Length

500 Mpts (350/500 MHz, single-channel mode), 100 Mpts (250 MHz)

Display

10.1-inch LCD, 1024 × 600, multi-touch

Serial Decode

UART/RS-232, I²C, SPI, CAN, LIN (standard)

Built-in AFG (HG only)

2 channels, 50 MHz, 160 MSa/s, 14-bit

Interfaces

USB 2.0 host ×3, USB 2.0 device ×1, LAN, Type-C power input

Authorized partner since 2012
Local FAE & application engineering
Hands-on training & integration
Manufacturer warranty

About GDS-2000HD/HG Series 12-bit Digital Storage Oscilloscope

The GW Instek GDS-2000HD/HG Series is a 4-channel digital storage oscilloscope built around a 12-bit ADC, giving 4096 vertical levels where an 8-bit scope has 256. It comes in three bandwidths, 250 MHz, 350 MHz and 500 MHz, and two variants: the HD models are oscilloscopes, and the HG models add a built-in 50 MHz arbitrary function generator with Frequency Response Analysis (Bode plots). An Android-based operating system drives a 10.1-inch multi-touch display.

GW Instek GDS-2504HD 12-bit 500 MHz oscilloscope, front view, available in India from GSAS Micro Systems

GDS-2000HD/HG model lineup

ModelBandwidthChannelsMax record lengthBuilt-in AFG
GDS-2254HD250 MHz4 + EXT100 MptsNo
GDS-2354HD350 MHz4 + EXT500 MptsNo
GDS-2504HD500 MHz4 + EXT500 MptsNo
GDS-2254HG250 MHz4 + EXT100 Mpts2-ch, 50 MHz
GDS-2354HG350 MHz4 + EXT500 Mpts2-ch, 50 MHz
GDS-2504HG500 MHz4 + EXT500 Mpts2-ch, 50 MHz

The 500 Mpts figure applies in single-channel mode; in dual-channel mode the 350 MHz and 500 MHz models record 250 Mpts. GW Instek specifies the 500 MHz bandwidth with one channel enabled in each channel pair (CH1/CH2 and CH3/CH4).

Key specifications

SpecificationGDS-2000HD/HG Series
Vertical resolution12-bit; 1 MΩ: 500 µV/div to 10 V/div; 50 Ω: 500 µV/div to 1 V/div (500 µV/div is a digital magnification of 1 mV/div)
DC gain accuracy≤ 1 mV: ±3%; 2 mV: ±2%; ≥ 5 mV: ±1.5%
Real-time sample rate2.5 GSa/s (half channels), 1.25 GSa/s (all channels)
Time base accuracy±2 ppm, about 1 ppm increase in error per year
Rise time1.75 ns (250 MHz), 1 ns (350 MHz), 0.7 ns (500 MHz)
Acquisition modesSample, Peak, High Res, Average, Segmentation
Waveform capture rate50,000 wfms/s real-time, 500,000 wfms/s segmented (test conditions: single channel, 1k memory depth)
Trigger typesEdge, Pulse Width, Video, Pulse Runt, Rise and Fall, Windows, Nth Edge, Logic, Time out, Bus
Analysis1 Mpts FFT, 43 automatic measurements with statistics, DVM, 6-digit frequency counter, digital filters
Display10.1-inch LCD, 1024 × 600, multi-touch
InterfacesUSB 2.0 high-speed host ×3, USB 2.0 high-speed device ×1, LAN (10/100 Mbps), Type-C power input
PowerAC 100 V to 240 V, 50/60 Hz; under 35 W without generator, under 50 W with generator
Dimensions / weight325 × 209.5 × 111.5 mm; approx. 3.2 kg

12-bit resolution for power and analog work

With 4096 vertical levels, the GDS-2000HD/HG resolves small ripple, low-level sensor signals and distortion that an 8-bit scope quantizes into steps. GW Instek specifies ±1.5% DC gain accuracy at 5 mV/div and above and a ±2 ppm time base, which matter when you calculate switching losses or analyse frequency and phase. Standard serial trigger and decode covers UART/RS-232, I²C, SPI, CAN and LIN, so embedded and automotive bus debugging needs no extra licence.

HG models: built-in 50 MHz generator and Bode plots

Each HG model adds a 2-channel arbitrary function generator: 50 MHz maximum frequency, 160 MSa/s, 14-bit vertical resolution, 28 built-in waveforms and an output range of 2 mVpp to 10 Vpp into high impedance (up to 10 MHz). A one-key copy function sends a captured waveform to the generator so a real-world anomaly can be replayed into the device under test. The HG models also run Frequency Response Analysis, plotting gain and phase to check loop stability and phase margin in switching power supplies and filters. Choose an HG if you need stimulus and response on one instrument.

Android interface, remote control and field use

The Android-based system supports multi-touch operation, screen recording, built-in WPS Office for documents and PDFs, peripheral support and Web Control for remote operation over the network. The oscilloscope weighs approximately 3.2 kg and accepts Type-C power from an adapter or battery that supports the 12 V handshake protocol at 48 W, so it can be taken to a vehicle or a field site. The menus are available in 11 languages, and GW Instek provides OpenWave PC software and a LabVIEW driver.

Applications

  • Switching power supply design: ripple, switching-loss and loop-stability measurements (Bode plots on HG models).
  • Automotive and embedded debugging: CAN, LIN, SPI, I²C and UART trigger and decode.
  • Engineering verification and product development: deep memory for long captures at high sample rates.

Buy the GDS-2000HD/HG in India from GSAS Micro Systems

GSAS Micro Systems is an authorized GW Instek engineering partner for Karnataka, Andhra Pradesh and Telangana, supporting customers across India. We help you choose the bandwidth and the HD or HG variant, arrange a demonstration on your own signals, and provide GST-compliant quotations with probe and accessory recommendations. Teams in Bengaluru, Hyderabad, Chennai, Pune, Mumbai and Delhi NCR can request a quote or book a demo. For a summary of the launch alongside the SPS-A power supplies, read our GDS-2000HD/HG and SPS-A launch post.

Common questions about GDS-2000HD/HG Series 12-bit Digital Storage Oscilloscope

What is the difference between the GDS-2000HD and the GDS-2000HG?
Both are 4-channel, 12-bit oscilloscopes in 250 MHz, 350 MHz and 500 MHz versions, and GW Instek publishes one oscilloscope specification for both. The HG models add a built-in 2-channel, 50 MHz arbitrary function generator (160 MSa/s, 14-bit, 28 built-in waveforms) and Frequency Response Analysis for Bode plots. The HD models have no generator.
Does the 500 MHz model give 500 MHz and 2.5 GSa/s on all four channels?
No. GW Instek's datasheet specifies 500 MHz bandwidth when only one channel in each pair (CH1/CH2 and CH3/CH4) is enabled, and 2.5 GSa/s on half the channels under the same condition. With all four channels on, the real-time sample rate is 1.25 GSa/s.
How much memory does the GDS-2000HD/HG have?
The 350 MHz and 500 MHz models record up to 500 Mpts in single-channel mode and 250 Mpts in dual-channel mode. The 250 MHz models record up to 100 Mpts.
Can the GDS-2000HD/HG run from a power bank?
GW Instek lists a Type-C power supply interface. The adapter or battery must support the 12 V handshake protocol and supply 48 W. The instrument weighs approximately 3.2 kg.
How do I buy the GW Instek GDS-2000HD/HG in India?
GSAS Micro Systems is an authorized GW Instek engineering partner for Karnataka, Andhra Pradesh and Telangana, supporting customers across India. Request a quote with the bandwidth you need and whether you need the HG generator, and GSAS will provide INR pricing, a GST-compliant quotation and a demonstration.

Interested in GDS-2000HD/HG Series 12-bit Digital Storage Oscilloscope?

Get pricing, an evaluation unit, or a technical consultation from our application engineers.

Request a Quote Demo